Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Tallahassee?
Chimney liner and rebuild work in Tallahassee typically runs from about $1,900 to $3,400 for a stainless-steel liner on a standard one-story flue, and $2,800 to $9,500 or more for a rebuild of the firebox, crown or upper stack. The wide range comes down to flue length, whether HeatShield resurfacing can save the existing liner instead of replacing it, and how much masonry has to come apart before it can go back together safely. Every price we give is an estimate set by a written quote after we’ve seen the flue, so the number you’re quoted is the number you pay.
Key Takeaways
- A standard DuraFlex stainless liner for a one-story Tallahassee home usually lands between $1,900 and $3,400, installed.
- HeatShield ceramic resurfacing is often cheaper than a full reline when the flue is compromised but still structurally sound – typically $1,400 to $2,600.
- Firebox rebuilds on older brick chimneys run $2,800 to $6,500; full stack rebuilds go higher.
- Our technicians have up to 14 years of experience, and one call covers sweep, repair and inspection – in-house.
- Free estimates. Call (855) 904-4110. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Chimney Liner & Rebuild Cost Breakdown (2026)
Here’s how the work breaks down on a typical Tallahassee job. These are estimated ranges for a residential chimney; the written estimate after inspection sets the final number.
| Service | Typical Range | What It Covers |
|---|---|---|
| Level 2 inspection (camera + report) | $275 – $475 | Documented condition of flue, firebox and cap; useful for insurance and real estate |
| HeatShield liner resurfacing | $1,400 – $2,600 | Ceramic resurfacing of a compromised but structurally sound flue |
| DuraFlex stainless liner (one-story) | $1,900 – $3,400 | Full flexible liner, insulation, top plate and cap |
| DuraFlex liner (two-story / long flue) | $3,200 – $5,800 | Extended liner run, insulation and full termination |
| Firebox rebuild | $2,800 – $6,500 | Re-laying firebrick, parging and damper work |
| Crown repair or rebuild | $650 – $2,200 | Crown sealing or full rebuild with proper slope |
| Full stack rebuild (upper flue) | $5,500 – $9,500+ | Removing and rebuilding the section above the roofline |
| Cap, damper and venting components | $280 – $850 | Famco and Gelco caps, top-sealing dampers, venting |
What pushes a quote up or down? The big drivers are flue length and the number of offsets the liner has to pass through, whether the existing flue is clay tile, pumice or an older single-wythe build, and how much of the firebox or crown has actually failed versus just stained. A chimney that’s been swept regularly and only needs a liner goes toward the low end. A chimney that’s never been inspected, with crumbling mortar joints and a cap that came off years ago, tends to run higher because more of the system has to be rebuilt, not just lined. Materials matter too – DuraFlex and HeatShield are twice the upfront cost of generic liner stock at a big-box store, but they’re the same lines certified chimney professionals use nationwide, and that’s what we install.
What Affects Chimney Liner & Rebuild Pricing in Tallahassee
Two homes on the same street can get very different quotes. Here’s what actually moves the number:
- Flue length and roof height. A one-story ranch in Killearn or Betton with a short flue is a different job than a taller, steep-pitch home near Myers Park, where the liner run and the safe access to the top both add labor and time.
- Type of failure. A flue with cracked clay tiles but sound mortar can often be sealed with HeatShield. A flue with spalling brick, missing mortar joints or a collapsed crown usually means tearing out and rebuilding – and rebuild work costs several times what resurfacing does.
- Firebox condition. Older brick fireboxes with deteriorated firebrick and a rusted damper almost always need re-laying. That work alone can add $2,800 to $6,500 to the job.
- Cap and top hardware. A missing or improvised cap lets rain and pests into the flue, which is the most common cause of accelerated failure in this climate. A properly fitted Gelco or Famco cap and a top-sealing damper correct that from the top down.
- Draft and venting problems. Tallahassee’s long, humid cooling season and frequent afternoon thunderstorms mean a lot of chimneys that sit unused for months develop odor and downdraft issues. Sometimes that’s a venting correction (a Gelco or Famco component change), sometimes it’s a sign the flue itself has failed – the inspection tells you which.
- Inspection level. If there’s a real estate transaction, a recent chimney fire or a flue that’s never been camera-scanned, a Level 2 inspection is the right starting point before anyone quotes a repair. We document system condition formally so you have a record for insurance or title.
Liner Repair vs. Liner Replacement: Which Costs Less?
HeatShield resurfacing is usually the cheaper route when the flue is still structurally sound, and it’s the option we recommend first if the camera shows a repairable substrate. It’s a ceramic resurfacing system that restores a compromised liner from the inside, and it typically runs several hundred to over a thousand dollars less than a full reline. But resurfacing only works when the existing flue has enough integrity to hold the new coating. If the tiles are shifting, the mortar joints are gone or the flue has separated, a HeatShield application won’t last – and that’s where a DuraFlex stainless liner is the right call.
DuraFlex is the industry standard for flexible stainless liners, and it’s what we install for relining. On a one-story home it’s typically $1,900 to $3,400 installed; on a two-story or long flue it goes higher. That’s more than resurfacing, but it also gives you a new, insulated flue liner rated for the appliance. If you’re weighing the two, a camera inspection is the only way to know which applies. We won’t sell you a liner when resurfacing will do, and we won’t resurface a flue that needs replacing.
If the problem is masonry above the roofline – crumbling crown, spalling brick course, a stack that’s pulling away – that’s rebuild territory, not liner work. That’s a different job with a different range, and it starts with a look at the outside of the chimney, not the inside.
Why Chimney-Only Specialists Cost More Up Front (and Less Overall)
General handymen will quote a liner, and some will do a decent job. The reason we stay chimney-only is that a firebox and flue system isn’t a siding repair – it’s a safety-critical vent, and the line between “fine” and “failing” is usually out of sight. A general contractor quotes from the roof; a chimney specialist quotes from a camera pulled through the flue.
That’s also why we work with professional-grade brands on every job: DuraFlex for liners, HeatShield for resurfacing, Gelco and Famco for caps and venting, Olympia Chimney and Copperfield for other components. These are the same lines certified chimney professionals use nationwide. They’re not the stock sitting on a hardware-store shelf, and that’s reflected in the price. It’s also why we can tell you honestly whether your system needs a $1,900 repair or a $6,000 rebuild instead of guessing.
We perform sweeping, repair and inspection in-house, one specialist covering every part of the system. If you’ve had a general handyman quote a reline without a camera inspection, that’s the one to be suspicious of – a liner without an inspection of the existing flue is a guess.
Safety First: Why Liner and Rebuild Work Isn’t a DIY Job
Flue liners and firebox rebuilds sit inside one of the most dangerous parts of the house. Liner installation requires sealing against carbon monoxide leaks, maintaining correct clearances to combustibles, and proper termination above the roofline. Rebuilds involve high-tension structural masonry work on a roof. We don’t advise homeowners to attempt either. A backdraft or a cracked liner after a bad install can vent combustion gases into living space, and that’s a risk no homeowner should take. Get it inspected, get a written quote from a trained professional, and get it done right.
How to Save on Chimney Liner & Rebuild
A few practical ways to keep the number down without cutting corners:
- Get it inspected before it’s a rebuild. The most expensive chimney jobs are the ones where a small crown crack or missing cap was ignored for years. A $275 to $475 inspection can catch a problem while HeatShield resurfacing or a cap replacement still solves it.
- Sweep on schedule if you burn wood. A creosote buildup is a fire hazard, and regular sweeping keeps you from discovering a burned liner after the fact. Annual sweeping is cheap next to a reline.
- Bundle inspection with sweeping. Scheduling a sweep through our Tallahassee chimney sweep team and letting the same visit include inspection means you get a full picture without paying for two visits.
- Get the estimate in writing before any work starts. Every quote we give is free and set per job in writing. Call (855) 904-4110 for a free estimate – no surprises later.
- Don’t skip the cap. A properly fitted cap is one of the cheapest forms of insurance against a liner failure. Gelco and Famco caps cost a fraction of a reline and keep rain, debris and pests out of the flue.
What’s It Like Living With a Wood-Burning Fireplace in Tallahassee?
Homes in Tallahassee have a specific chimney rhythm. Winters are mild enough that many fireplaces sit cold for weeks, then get a few real burns when a front pushes through. That long idle period is when condensation, nesting pests and cap failures do their damage quietly. By the time a homeowner notices smoke coming back into the room or a smell when the fireplace isn’t even lit, the flue has usually been in trouble for a while.
Add the summer humidity – chimneys in this part of North Florida don’t get the deep freeze others do, but they do get months of warm, wet conditions with no fire to dry the flue out. Crowns crack, mortar joints soften, and the cap takes the beating. That’s why we ask new homeowners in Tallahassee to get a formal inspection before their first season, and why Level 2 inspections matter for any recent purchase. We document condition formally so you have a record for insurance, title or a maintenance log.
If your house is more than a couple of decades old and you don’t have a record of the last inspection, assume it’s due. It’s a much easier conversation to have before a rebuild than after.
FAQs – Chimney Liner & Rebuild Cost
How much does a chimney liner cost in Tallahassee?
A stainless-steel DuraFlex liner for a standard one-story Tallahassee home typically costs $1,900 to $3,400 installed, and a two-story or long-flue install runs $3,200 to $5,800. The written estimate after a camera inspection sets the final price. Call (855) 904-4110 for an exact quote – estimates are free.
Is it cheaper to repair or replace a chimney liner?
Repairing is cheaper when the flue is still structurally sound. HeatShield ceramic resurfacing runs $1,400 to $2,600, while a full DuraFlex liner replacement runs $1,900 to $3,400 on a one-story home. Resurfacing only works if the substrate holds. A camera inspection tells you which applies. Call (855) 904-4110 for a free estimate.
How much does a chimney rebuild cost in Tallahassee?
A firebox rebuild typically runs $2,800 to $6,500, a crown repair or rebuild $650 to $2,200, and a full upper-stack rebuild $5,500 to $9,500 or more. The scope after inspection sets the final number. Call (855) 904-4110 for an exact quote – estimates are free.
Does a chimney liner really cost this much, or can I use a cheaper generic liner?
A full liner install with proper insulation, top plate and cap is $1,900 to $3,400 for a one-story home, and yes, that’s more than the box-store liner you might have seen. We install DuraFlex, the same line certified chimney professionals use, because a cheap liner without proper insulation and sealing can fail and vent carbon monoxide into the house. The written estimate sets the price. Call (855) 904-4110 to book a free estimate.
Can you come today?
Same-day service is often available, and a call before dispatch gets you on the schedule. We answer 24/7 and dispatch Sunday through Friday, 7am to 7pm; a call outside those hours is booked into the next opening. Call (855) 904-4110 to schedule a free estimate.
Do you do the inspection and the repair, or refer it out?
We do both. Inspection, sweeping and repair are all in-house, so a single visit can cover the camera inspection, a written report and the repair quote. That means no coordinating between contractors and no gaps between what the camera saw and what gets fixed. Call (855) 904-4110 to get started.
Get a Written Estimate Before Anything Else
Pricing on a chimney liner or rebuild is only as good as the inspection behind it. Our technicians have up to 14 years of experience, and we work with professional-grade brands – DuraFlex for liners, HeatShield for resurfacing, Gelco and Famco for caps and venting – because the flue is a safety system, not a cosmetic one. Whether you’re in Tallahassee and need a liner, a rebuild or just a camera look before you buy a home, we’ll quote it in writing so you know exactly what you’re paying for. Free estimates. No surprises later. Call (855) 904-4110. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Tallahassee market as of 2026. Tallahassee Chimney Sweep offers free estimates – call (855) 904-4110.
Written by the team at Tallahassee Chimney Sweep.
What Our Customers Say
"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."
- Matt Ackerman"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."
- Lamont Ingram"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Dana Sutton