Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Tallahassee Homeowners
Most chimney problems in Tallahassee announce themselves quietly: a faint creosote smell on a warm day, a hairline crack in the crown, a stainless cap that’s lost a screw and now sits crooked. Water gets in, masonry weakens, and a small repair becomes a large one. Our technicians have up to 14 years of experience and work only on chimney systems – sweeping, repair, and inspection, all in-house. We use professional-grade materials like DuraFlex and HeatShield, not hardware-store substitutes. Same-day repair is available, and the phone is answered around the clock. Call (855) 904-4110.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a protective cover over the flue opening, and in Tallahassee it’s the single cheapest way to keep rain, birds, squirrels, and debris out of a chimney. A proper cap lets smoke and gases out while blocking everything else. We fit Gelco and Olympia Chimney caps measured to the actual flue, not a universal size forced to fit. Typical installation runs $150 to $450 depending on flue count, cap style, and whether the crown needs work first. Nothing is charged until a written estimate is agreed.
Why a Cap Matters in This Climate
Tallahassee gets heavy summer rain that drives sideways onto roofs, and an open flue takes water straight into the firebox and liner. That moisture mixes with creosote deposits and rusts steel components from the inside. A correctly fitted cap stops the water before it ever gets inside.
Single-Flue and Multi-Flue Caps
Homes here often have one flue for the fireplace and a second for a furnace or water heater, so a multi-flue cap needs careful measurement and clearance. We check that the cap doesn’t obstruct draft or sit too close to a hot termination. Spacing matters as much as the cap itself.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is the removal and refitting of a cap that has rusted through, warped, or lost its mesh, and it’s usually a same-day job. Once the mesh tears, animals and sparks get through; once the top rusts, water sits on the flue. We source replacement caps through Gelco and Olympia Chimney and match the new cap to the existing crown and flue size. Typical cost is $150 to $500 depending on how much of the old hardware has seized. The written estimate sets the final price.
Spotting a Failed Cap
Look for rust streaks down the masonry, a cap that’s visibly tilted, or mesh with holes large enough for a bird to enter. A cap that rattles in wind is often one fastener away from coming off. Any of these means it’s time to have it looked at.
Disposal and Re-Fit
Old caps can be welded or bolted on hard enough to need cutting, and we handle removal without damaging the crown below. The new cap is anchored properly, not just set in place. We confirm it’s square and secure before we leave the roof.
Chimney Liner Installation
Chimney Liner Installation is the fitting of a new flue lining, and it becomes necessary when the existing clay tile is cracked, offset, or missing in sections. A damaged liner lets heat reach framing and lets carbon monoxide escape into the house, which is why it isn’t a job to defer. We install DuraFlex stainless flexible liners sized to the appliance, and where the flue is intact but pitted we restore it with the HeatShield ceramic resurfacing system. Typical liner installation in Tallahassee runs $1,800 to $4,500 depending on height, flue condition, and insulation requirements. It’s never a DIY job – this is trained-professional work.
Clay Tile Versus Stainless
Original clay tiles crack over time, especially after a chimney fire or a long period of disuse. A stainless liner creates a continuous, sealed flue that’s rated for the appliance it serves. It’s a permanent fix rather than a patch.
When Resurfacing Beats Relining
HeatShield is designed for flues where the structure is sound but the surface has deteriorated. It restores integrity from the inside without tearing out tile. We only recommend it when camera inspection shows it will actually hold.
Chimney Flashing Repair
Chimney Flashing Repair addresses the metal that seals the joint between chimney and roof, and it’s where most Tallahassee roof leaks around a chimney begin. Flashing lifts, corrodes, or gets tarred over badly, and water finds the gap. We rework step and counter flashing so it sheds water the way it’s meant to, using proper metal rather than sealant alone. Typical repair costs $250 to $700 depending on roof pitch and how much old flashing must be removed. A free estimate confirms the scope before anything is booked.
Leaks That Aren’t the Roof
Homeowners often call a roofer first when the stain appears at the chimney. The stain usually traces to failed flashing, not shingles. We identify the actual entry point before anyone starts work.
Sealant Isn’t a Fix
Caulk and roof cement fail within a season or two under Florida sun and rain. Properly lapped metal flashing is what actually keeps water out. We replace the failed material rather than covering it.
Chimney Crown Repair
Chimney Crown Repair fixes the concrete cap at the very top of the chimney, and a cracked crown is one of the most common water-entry points we find in Tallahassee. The crown sheds rain away from the flue; once it cracks, water runs down inside the chimney and through the masonry. We repair or rebuild crowns with a proper slope and overhang so water leaves the structure. Typical cost is $350 to $900 depending on crack size and whether the crown needs full replacement. Repairs are priced per job on the written estimate.
Hairline Cracks Versus Structural Breaks
A hairline crack can often be sealed and resurfaced. A crown broken into sections usually needs rebuilding. Camera inspection and a close look at the top tell us which.
Why Slope and Overhang Matter
A flat or undercut crown holds water on the surface instead of shedding it. We build in the slope and overhang that keep water moving away from the flue. That detail is what makes a crown repair last.
Chimney Repair Companies
Chimney Repair Companies vary widely in what they actually do, and in Tallahassee the difference usually comes down to specialization. Some are general contractors who add chimneys as a side service; some subcontract the real work out. We handle sweeping, repair, and inspection in-house, so nothing gets handed to a third party. Repairs typically run $250 to $4,500 depending on the system involved, with the written estimate setting the final number. The estimate is free, and you’ll never be told you need work without camera evidence you can see yourself.
Questions Worth Asking
Ask whether the company performs the repair itself or subcontracts it, and whether it does chimney work exclusively. Ask what documentation you get after the visit. Vague answers tell you a lot.
What to Avoid
Be cautious of anyone who quotes a major liner replacement before inspecting the flue with a camera. A low sweep price that turns into a large repair bill on the same visit is a pattern worth recognizing. We show evidence before recommending anything.
Chimney Masonry Repair
Chimney Masonry Repair restores the brickwork and mortar joints that hold the chimney together, and it’s needed once spalling brick or crumbling mortar lets water in. In Tallahassee’s humid summers, mortar joints soften and brick faces flake; left alone, the chimney loses structural strength. We repoint joints, replace spalled brick, and address the source of the moisture rather than just cosmetically patching it. Typical masonry repair is $500 to $2,500 depending on the area involved and how much must be rebuilt. Any repair that can safely wait is noted in the report so you decide on your own timeline.
Repointing Versus Rebuild
Repointing replaces deteriorated mortar without disturbing sound brick. A rebuild is only needed when the brick itself has failed. We aim for the smaller repair when it’s the right one.
Finding the Moisture Source
Crumbling mortar is a symptom, not the cause. It’s usually a failed crown, cap, or flashing letting water in. We fix the source first, then the masonry.
Brands We Service
We install and service DuraFlex flexible liner systems, and we know exactly where they wear – at the top termination, at the appliance connection, and anywhere the liner bends. We also work with HeatShield ceramic resurfacing on compromised flues, and we fit Gelco and Olympia Chimney caps and components for a properly sealed top. These are professional-grade lines used by chimney specialists, not the generic parts sold at a big-box store.
We don’t claim to be a dealer for any of these brands, and we don’t stock parts on a truck. What we do is specify the right component for your flue and install it correctly – which matters far more than a brand label on its own. Our technicians have up to 14 years of experience with these systems. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Smoke rolling back into the room. A draft problem, a blocked flue, or a failed cap can all cause it, and it often signals something that needs eyes on it. Have it checked before the next fire.
- A strong creosote or sooty smell on warm days. That smell means deposits have built up and moisture is moving through them. It’s a warning sign worth acting on.
- Water stains or rust inside the firebox. Water is getting past the crown, cap, or flashing. Left alone, it damages the liner and masonry from the inside out.
- Crumbling mortar or loose brick on the chimney. The structure is losing strength, and in severe cases brick can fall. This is a safety matter, not just a cosmetic one.
- A damaged or missing cap. An open flue lets animals, rain, and sparks in, and a cracked cap fails fast. It’s a quick fix that prevents expensive ones.
Our Process, Step by Step
- 1
We listen first. We ask what you’ve noticed – smoke, smell, stains, noise – and what the fireplace or appliance is. The symptoms narrow down where to look.
- 2
We inspect with a camera. A flue camera shows the inside of the liner, the firebox, and the smoke chamber on a screen you can see. Nothing is guessed at.
- 3
We show you what we found. Photo evidence and a clear explanation of what’s failing and why. If work can safely wait, we say so.
- 4
We give you a written, flat-price estimate. The price is agreed before we book, and it’s set per job – no moving numbers on the day.
- 5
We do the work and document it. The repair is completed to the standard the system needs, and you get a written record of condition for real estate, insurance, or your own files.
How Much Does Chimney Repair Cost in Tallahassee?
Chimney repair in Tallahassee typically runs from about $150 for a cap installation up to $4,500 for a full liner replacement, with most single repairs landing between $250 and $900. The range is wide because the jobs are genuinely different: a crown crack and a collapsed flue tile aren’t the same problem, and they shouldn’t cost the same. A typical flashing repair runs $250 to $700 depending on roof pitch; a typical crown repair runs $350 to $900; masonry repointing usually falls between $500 and $2,500.
What affects the price most is access, how much old material has to come out, and how deep the damage goes once we see it. Height and roof pitch add labor. A repair that looks small from the ground can be larger once the failed section is opened up – and we show you why before quoting it. What keeps you from overpaying is simple: a detailed written estimate, camera evidence behind every recommendation, and an honest note when a repair can safely wait.
Every estimate is free, and it covers the inspection findings, the recommended scope, and a flat price per job. We don’t bill for a call-out or add a diagnostic charge. Call (855) 904-4110 for an exact quote – estimates are free.
Our Service Area Near Tallahassee
We serve homeowners across Tallahassee and the surrounding communities, including Bradfordville, Woodville, Crawfordville, Quincy, Monticello, Midway, Havana, Fort Braden, and Chaires. Most of these are a short drive, and our fast dispatch runs from 7am to 7pm, Sunday through Friday, so a booked visit is usually scheduled within a day or two of the call. If you’re in Bradfordville, you can read about chimney repair for your area; homeowners in Woodville can find local details on chimney repair as well. For the city itself, see our main Tallahassee Chimney Sweep page and our guide to chimney repair.
Serving Tallahassee, FL – Our Local Coverage Area
We serve Tallahassee and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Tallahassee
Chimney repair is the correction of any defect in the chimney system – the crown, cap, flashing, liner, masonry, or firebox – that affects safety or function. It’s distinct from sweeping, which removes deposits, and from inspection, which documents condition. Most repairs follow an inspection that identifies what has failed. Call (855) 904-4110 for a free estimate if you’re unsure which you need.
Most single repairs – a cap, a crown, flashing – take a few hours and are often done same day. A liner installation is a longer job, usually a full day, depending on how much of the old liner has to come out. We give you the expected time in the written estimate. Call (855) 904-4110 to talk through your situation.
Typical repairs run $250 to $900 for a single issue, with liner work at $1,800 to $4,500 and smaller jobs like a cap starting around $150. The exact figure depends on access, damage depth, and materials. The written estimate sets the final price, and the estimate itself is free. Call (855) 904-4110 for an exact quote.
Yes – we install and service DuraFlex flexible liners and apply HeatShield ceramic resurfacing for compromised flues. We also fit Gelco and Olympia Chimney caps and components. Our technicians have up to 14 years of experience with these systems. Whether you have one of these or another make, we can help.
Same-day repair is often available, and we answer 24/7. Fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (855) 904-4110 to schedule.
We stand behind the repairs we complete, and we confirm the terms in writing before the job is booked so you know what’s covered. Ask for the written terms when you get your estimate. Call (855) 904-4110 with any questions about coverage.
Clear access to the fireplace and hearth, move anything fragile away from the work area, and secure pets. If we need roof access, make sure the gate or ladder path is clear. That’s usually all it takes. Call (855) 904-4110 if you have specific concerns before the visit.
Schedule Your Chimney Repair Service in Tallahassee Today
If you’ve noticed a smell, a stain, or a cap that’s seen better days, it’s worth having it checked before the next fire. Call (855) 904-4110 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’ll walk you through what we find and what it actually needs – nothing more.
Written by the team at Tallahassee Chimney Sweep.